当前位置:网站首页 > 新闻动态 > 行业资讯
行业资讯 / Company news
  • 耐腐蚀泵需要怎么保养?
  • 本站编辑:杭州仁祥泵业有限公司发布日期:2018-07-16 13:49 浏览次数:
wQ潜污泵
在使用过程中不能等泵出问题了才想到维修,平时保养也是必不可少的,耐腐蚀泵是怎么保养的了?
In the process of using the pump can not wait for a problem, just think of maintenance, peacetime maintenance is also essential, how to maintain the corrosion pump?
1、检查泵及管路各结合处有无松动现象。用手转动泵试看泵是否灵活,然后试试看电机转向。
1. Check whether there is any loosening phenomenon at the junction of pumps and pipes. Use the hand to turn the pump to see if the pump is flexible, and then try the motor steering.
2、向悬架内加入轴承润滑机油,观察油位应在油标的两刻线之间。
2. Add bearing lubricating oil to the suspension. Observe the oil level between the two marking lines of the oil mark.
3、拧下泵体的引水螺塞,灌引水。
3, the water diversion plug of the pump body is screwed down, and the water is poured.
4、关好出水管的闸阀和出口压力表和进口真空表。
4. Close the gate valve and outlet pressure gauge of the outlet pipe and the imported vacuum gauge.
5、开动电机,当泵正常运转后,打工出口压力表和进口真空表,视其显示适当压力后,逐渐打开闸阀,同时检查电机负荷情况。
5, the motor, when the pump is normal operation, the export pressure meter and the import vacuum table, as it shows the appropriate pressure, gradually open the gate valve, at the same time check the motor load.
6、尽量控制泵的流量和扬程在泵标牌上注明的范围内,保证泵在高效率点附近长期运转,以便获得较大的节能效果。
6, as far as possible to control the flow of the pump and the lift in the range of the pump marked on the sign, to ensure that the pump is running for a long time near the high efficiency in order to obtain the maximum energy saving effect.
7、水泵的运转过程中,轴承升温不超过环境温度35度,比较高温度不超过80度。
7. During the operation of the pump, the temperature of the bearing does not exceed 35 degrees of the ambient temperature, and the maximum temperature does not exceed 80 degrees.
8、如发现泵有异常声应立即停车检查原因。
8, if the abnormal sound of the pump is found, the reason should be stopped imtely.
9、泵要停止使用时,先关闭闸阀、压力表,然后停止电机。
9, when the pump should stop using, first close the gate valve and pressure gauge, then stop the motor.
10、泵在工作的靠前个月内,经100小时更换润滑油。以后每隔500小时,换油一次。
10, the pump in the first month of work, after 100 hours to replace the lubricating oil. After every 500 hours, change the oil once.
11、经常调整填料压盖,保证填料室内的滴漏情况正常。
11. Adjust the packing gland regularly to ensure that the leakage in the packing room is normal.
12、泵在寒冬季节使用时,停车后,须将泵体下部放水螺塞拧开将水放净,防止冻裂。
12, when the pump is used in the cold winter season, after the car is stopped, the screw plug of the lower part of the pump body should be unscrewed to release the water and prevent the frost crack.
13、泵长期停用,须将泵全部拆开,擦干水份,将转动部位及各结合处涂以油脂装好,妥善保存。
13, the pump will be discontinued for a long time. All the pumps must be disassembled and dried. Dry parts and all joints should be coated with grease.

免责声明: 本站资料及图片来源互联网文章,本网不承担任何由内容信息所引起的争议和法律责任。所有作品版权归原创作者所有,与本站立场无关,如用户分享不慎侵犯了您的权益,请联系我们告知,我们将做删除处理!